Guide :Optics : Telescope

Hand controller im looking for a hand controller for a meade lx-10

Posted by tem54 on Dec 19, 2007

Research, Knowledge and Information :

Meade LX3 Hand Control Reproduction - Cloudy Nights

Meade LX3 Hand Control ... There are some details on the LX5 hand controller at the Yahoo Meade LX3 ... the vast majority of Meade LX models use a 180 tooth ...
Read More At :

meade lx200 hand controller | eBay

Meade 10" LX 200 LX200 telescope w extras. ... Not finding what you're looking for? Follow meade lx200 hand controller to get e-mail alerts and updates on your eBay Feed.

LX10 Hand Controller - Meade 4M Community

LX10 Hand Controller - posted in Meade Legacy Telescopes: I'm a newbie in the U.K. and recently purchased an 8" LX10 with Dec motor fitted. The keypad hand controller ...
Read More At :

8 LX90 Schmidt-Cassegrain Telescope with Autostar Hand Controller

8" LX90 Schmidt-Cassegrain Telescope with Autostar Hand Controller Meade Instruments Corporation. ... look at the Sun!Looking at or near the Sun
Read More At :

New LX200 Hand Controller -

While looking online for documentation for the LX200 I ran across a couple of joysticks that had been used with the LX200, ... New LX200 Hand Controller
Read More At :

Meade 10 inch LX200 Classic Keypad Hand Controller

I would appreciate some advice on a problem I encountered with the keypad hand controller for my 10 inch LX200. All of the keys work with the exception of the number ...
Read More At :

meade hand controller | eBay

Find great deals on eBay for meade hand controller and meade controller. ... Not finding what you're looking for? Follow meade hand controller to get e-mail alerts ...

LX200 Hand Controller / Keypad --

LX200 Classic Keypad or Hand Controller Analysis of ... (or hand paddle or hand controller) ... Hold the board so you're looking at the back of it and the bottom edge ...
Read More At :

Meade LX-10 8" - Excelsis

Weight includes optional field tripod.Comes with hand controller which controls side ... Telescope Reviews:Meade LX-10 8" Info Votes ... Meade's LX-10 page
Read More At :

Suggested Questions And Answer :

Azimuth motor gearing problem

Sounds like it could be that the worm gear is not meshing Look here for guidelines in the internals
Read More At : ETX-125EC (500 x 127mm) Telescope...

Motors won't turn

Check for shaft locks being engaged, and for motor bearing issues.
Read More At : 114EQDH4 (36 x 114mm) Telescope...

Motors won't turn

Are the batteries FRESH? if they are you may have a bad motor. Contact Meade customer service: sounds like BAD batteries. Try new ones first before sending it to Meade.
Read More At : 114EQDH4 (36 x 114mm) Telescope...

Meade Quartz Controller Model 784

You can send me an e-mail and I will try to help you as I have the very same Quartz Controller on my 20 year old 10" scope. [email protected] PS I am looking for a back up 784 controller for my scope.
Read More At : Meade...


Had the same problem. Took it to a dealer and we put a new controller on but the funny thing was that my old controller worked fine on another scope but it would not work on mine. Agreed with "Guest" above - Mead's after sales service is bad.
Read More At : 8" LX90 LNT Schmidt Cassegrain Telescope with SmartFinder w/......


Most problems tend to be mechanical. Have you 'trained' the drive and set the backlash values? Those 2 can have dramatic effects on pointing accuracy. Also, if the optical tube is not in alignment with the mount, then nothing will work correctly. To check that, have the telescope in Alt-Az configuration, inside the house, loosen the RA lock, and shine a laser pointer on the corrector plate. as the telescope is rotated about the RA, the reflected spot should be steady. Adjust the DEC to minimize the diameter of the circle that is drawn. What is left, is the out-of-true on the DEC axis. That can be adjusted with the tube cradle alignment bolts.
Read More At : Meade...

I am trying to extend my 494 hand controller lets say to a reasonable length, lets say 15 feet instead of the 6 foot with the unit. I am using a good ethernet cat 5 cable with an extension coupler, same pin out 1 goes to 1 , ohm this out all seems fine, but the controller doesn't respond, wants be to enter n,s,e,w,u,p ,d keys then says "self test" failed Any help out there? Telescope is a meade ds2130s.

Either you have a bad hand controller or your cable configuration is sells a longer coiled cable already made up-- it is very good quality. Order one:
Read More At : DSX102AT Telescope...

Hand controller im looking for a hand controller for a meade lx-10

I would check the classifieds at cloudy nights forum or ask around there. most likely one should show up.. Or someone will know how to build one.
Read More At : Telescope...

Meade LX200GPS 8" won't initialize on power up.

Try doing either a garbage collect or a safe load-- and then reinstall the hand controller firmware-- Instructions-- depending on the type of controller Autostar 495 or 497: You enter Safe Mode by holding the [enter] and[scroll down] keys pressed when you power up the telescope. TheAutostar will say "Flash Load Ready"... now go start the ASU.Autostar II: if you need to use Safe Mode to recover from a disaster,turn on the telescope, and key 999 before it says "Initializing"The Autostar will say "Flash Load Ready"... now go start the ASU.LX200gps: BEFORE proceeding further, click on the OPTIONS item on the Top Bar. Now click on "Garbage Collect Hbx" ... this will perform data cleanup within the Autostar which will avoid potential mess-ups.
Read More At : LX200GPS Telescope...

My telescope fellover & the counter balance mount broke. Am I able to purch a replacement part. If so can I get a parts breakdown? The model is a Meade model 114EQ-DH4 4.5 Equatorial Reflecting Telescope w/starfinder Electronic Hand Controller. Thank you for your help in this matter. Leo McGroarty [email protected]

Contact Meade customer service:
Read More At : 114EQDH4 (36 x 114mm) Telescope...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0998 seconds