Guide :Optics : 494 AutoStar Telescope Control Unit (Handbox only)

Stalling out why does my 1989 ford f 150 keep stalling out while driving, sometimes it will start back up sometimes it won't?

Posted by ford man 60 on Mar 23, 2008

Research, Knowledge and Information :


stalling out coming to a stop - Ford F150 Forum


... drops way down and sometimes stalls or the idle pops back up and the ... My truck stalls out when coming to a stop. It's like ... to keep driving while I ...
Read More At : www.fordf150.net...

Ford E150 351 V8 stutter stall issue.wmv - YouTube


Aug 08, 2012 · My 1994 e-150 has a major issue that I'm struggling to figure out. ... Ford E150 351 V8 stutter stall ... Ford F-150 1993 Starts, runs. Turn off, Won't ...

F150 Stalls while driving down road


F150 Stalls while driving down road ... I waited a while and it fired up. This morning it didn't want to stay ... I have a 2007 Ford Truck F 150 2WD V8-5.4L VIN V ...
Read More At : www.justanswer.com...

Ford F-150 Questions - Won't start - CarGurus


Went out next morning to start it and it cranks but won't start. ... a little while it wont start back up and doesn't ... Ford F-150 cranks but won't start, ...
Read More At : www.cargurus.com...

Ford F-Series Stalling and No Start Problems — Car Forums at ...


Ford F-Series Stalling and No Start ... Mother has a 2005 ford 150 ... that has on several occasions stalled while driving down the road and come to a ...
Read More At : forums.edmunds.com...

Suggested Questions And Answer :


Stalling out why does my 1989 ford f 150 keep stalling out while driving, sometimes it will start back up sometimes it won't?


You posted this in the Telescope forum by mistake.
Read More At : 494 AutoStar Telescope Control Unit (Handbox only)...

Meade Autostar handbox


Because this is a new purchase i would suggest getting the handbox replaced under warranty. If the guy was rude, then mention this to their management. There have been quite a few prolems with meade gear on our site here. Handbox included. If you are up to it you can open it up. if so inspect the board for damage, shorts or loose solder joints. Some of these things can be repaired, some cannot. On this last statement it would seem sensible to get the replacement then start again from scratch. I have found about 7 recent problems with this unit, so be aware this is not a fault free unit.nettiser
Read More At : 494 AutoStar Telescope Control Unit (Handbox only)...

Telescope control unit AUTOSTART failure


Hi,I think your control unit is "bricked"; that is it was in the middle of an upgrade and lost power, the new firmware has not been completely written while the old has been deleted.However, based on your query "another method to communicate" and since your control unit uses RS-232 serial interface adapter, might not what you need is another communications method other than the PC astronomical software program or with the Autostar Suite software or whatever it is currently using? Have you tried "Hyperterminal"? I just do not think it is available in Vista, XP and lower Windows only.For reference and further information, pls check here and/or here.Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.Good luck and kind regards. Thank you for using FixYa.
Read More At : 494 AutoStar Telescope Control Unit (Handbox only)...

Little or no display - Meade 494 AutoStar Telescope Control Unit (Handbox only)


That does not help in troubleshooting - can you be more specific?
Read More At : 494 AutoStar Telescope Control Unit (Handbox only)...

Message...Proc. trap 2 what does it mean ? - Meade 494 AutoStar Telescope Control Unit (Handbox only)


It means the firmware is corrupted.It may be possible to reset it from software. Try and reload the Autostar firmware from a PC. (Download the updater application from Meade's website. http://www.weasner.com/etx/autostar_info http://www.meade.com/support/index.html
Read More At : 494 AutoStar Telescope Control Unit (Handbox only)...

Meade 494 autostar alignment - telescope not stopping for confirmation


Best I can do for youhttp://www.weasner.com/etx/menu.html
Read More At : 494 AutoStar Telescope Control Unit (Handbox only)...

My meade autostar controller seams to be messing up . its a 494 the bottom motor just goes around and around. do I need a new controller or what??


My autostar controller wouldn't go up or down. openned up and there seams to be a spring missing or something to force the cam together. anyone have a exploded view
Read More At : 494 AutoStar Telescope Control Unit (Handbox only)...

Meade LX200GPS 8" won't initialize on power up.


Try doing either a garbage collect or a safe load-- and then reinstall the hand controller firmware-- Instructions-- depending on the type of controller Autostar 495 or 497: You enter Safe Mode by holding the [enter] and[scroll down] keys pressed when you power up the telescope. TheAutostar will say "Flash Load Ready"... now go start the ASU.Autostar II: if you need to use Safe Mode to recover from a disaster,turn on the telescope, and key 999 before it says "Initializing"The Autostar will say "Flash Load Ready"... now go start the ASU.LX200gps: BEFORE proceeding further, click on the OPTIONS item on the Top Bar. Now click on "Garbage Collect Hbx" ... this will perform data cleanup within the Autostar which will avoid potential mess-ups.
Read More At : LX200GPS Telescope...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.opticinfobase.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0514 seconds