Guide :Optics : Yardage Pro 600 Rangefinder

Sight target needs adjustment

When i look through the viewfinder the displays are too high. I can barely see the target strength meter at the top it's so high. Naturally, when i put a target in the cross hairs the yardage isn't close to being right because the aim is off.

Research, Knowledge and Information :


SIGHT ADJUSTMENT AND ZEROING


required for sights that are not shown, you may need ... Features on target sights ... SIGHT ADJUSTMENT AND ZEROING Sights sold with most rifles manu-
Read More At : thecmp.org...

How to adjust an iron sight - Wikiversity


How to adjust an iron sight. From Wikiversity. ... then adjust the sights so they are pointing at the hole in the ... Many target sights have click adjustments, ...
Read More At : en.wikiversity.org...

Iron sights - Wikipedia


Iron sights are a system of shaped alignment ... Sight adjustments are orthogonal, ... Many target sights are designed with vertical or even undercut front sight ...
Read More At : en.wikipedia.org...

How To Adjust Sights On A Hand Gun - youtube.com


Nov 15, 2012 · How To Adjust Sights On A Gun. ... Need to report the video? ... How to Align Your Gun Sights on Target - Duration: 4:51.

Zeroing the Iron-Sights on Your AR-15 Rifle - Stag Arms LLC


Before you take your new AR-15 out for target practice or into the field to do some hunting, the first thing you will need to do is zero in the iron-sights.
Read More At : info.stagarms.com...

How to Adjust Gun Sights | Gone Outdoors | Your Adventure Awaits


How to Adjust Gun Sights ... if the bullet is hitting right of the target, adjust the front sight by moving it to ... Items you will need. Sight adjustment tool; Target;
Read More At : goneoutdoors.com...

How are iron sights on a rifle calibrated and used in shooting?


How are iron sights on a rifle calibrated and used ... here are the adjustment rules: Front sight post ... landing grouped in the center of your target, ...
Read More At : www.quora.com...

Tips for Sighting-In Your Bow - Petersen's Bowhunting


An article from Bill Winke that gives tips for sighting-in your bow ... adjustment of the sight head ... gun without a rear sight, your bow also needs a ...
Read More At : www.bowhuntingmag.com...

Holographic Weapon Sights FAQ | EOTech


EOTech holographic weapon sights FAQ ... the target will be in ... you are moving the image to the fixed point of aim so your adjustment dials on the sight are ...
Read More At : www.eotechinc.com...

Suggested Questions And Answer :


Sight target needs adjustment


I also had the same problem my Yardage Pro Compact 600. We live in the desert and I often leave my golf bag in the trunk of the car. One day the display on the rangefinder was shifted up so I assumed that the heat affected something. After checking with Bushnell, their answer was to ship it in and couldn't guarantee a cost. So I also peeled back the rubber grips from the bottom - you only need to go far enough to unscrew the four screws. From there you have to snap apart the case so the top shell comes off (be sure to remove the battery and cover first). Once you've done that, unscrew the top circuit board (mine only had 2 of the 4 screws from the factory). Be careful not to unplug any of the 3 ribbon cables. Move the top circuit board aside. Looking from the top front, there is an assembly at the back that holds the laser/reader, it is held in by 3 screws, 2 on the back left and 1 on the back right - remove them. Carefully remove the assembly leaving the 2 ribbon cables in tact. The 3rd (largest) ribbon cable is taped to the center sighting barrel. Gently remove the tape, the ribbon cable disappears into a **** in the back of the sighting barrel near the eyepiece, it is connected to the LCD display. Now flip the unit around and looking from the back eyepiece, remove the 2 screws near the ribbon cable. Now you should be able to lift the eyepiece up and away from the sighting barrel. The ribbon cable and LCD window at the end of the cable should be glued on two corners inside the eyepiece (worse case the LCD is loose as mine was because the glue had deteriorated). First scrap out the old glue from the LCD and eyepiece frame, being careful to not let the remnants drop inside the eyepiece or you will see these in the viewfinder once you get it back together! Using thick superglue and being careful not to touch the LCD and leave a smudge (or forget how it came out as your yardage display will be backwards!), put a tiny drop of glue on each lower corner of the eyepiece frame. Now carefully position the LCD window and push down to the bottom of the eyepiece frame. Try to center it left to right as near as possible (mine had a little gap on each side) while holding the LCD against the bottom edge. Keep it there until the glue dries. Now reassemble everything, making sure the sighting barrel and especially the laser/reader assembly fits snugly in its cradle before reinstalling the 3 screws, then install the top circuit board. Snap the top cover back on and before putting the 4 cover screws in, put in the battery/cover and test it. Remember if your display is reversed you installed the LCD backwards!
Read More At : Yardage Pro 600 Rangefinder...

Need an instruction manual for a bushnell pro 500


This can be obtained by calling bushnell customer service at 1-800-423-3537.
Read More At : Yardage Pro 500 Rangefinder...

Yardage pro 1000


Has laser been cleaned properly?
Read More At : Yardage Pro 1000 Rangefinder...

I've got a Bushnell Yardage Pro Laser Riflescope. The upper part of the digital LED display is "hidden" and it's hard to tell the difference between 7 and 1 when ranging. Are there any adjustments to be made, like "tilting" the display down? There are two sealed screws close to the eye lens underneath the scope, but I'm unsure if they've got anything to do with adjustment of the display. Any suggestions?


I wish i could find out why my yardage pro scope has the led display hidden too! I think for all the money they cost its rubbish
Read More At : 4-12 x 42mm Laser Rangefinder Riflescope...

Need a manual - Bushnell Yardage Pro 500 Rangefinder


Www.bushnell.com resources and manual archives.
Read More At : Yardage Pro 500 Rangefinder...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.opticinfobase.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0647 seconds