Guide :Optics : DS-2114 ATS (325 x 114mm) Telescope

Plastic gear I cannot find suppliers for my broken plastic gears and others parts I need. DO yoy know where i can find a detailed part list for the ds2114 and dealers non only in Itsly where i can order them? Many thanks. Carlo Giacch? - Perugia - Italy

Posted by carlog on Jul 11, 2008

Research, Knowledge and Information :



We did not find results for: plastic gear i cannot find suppliers for my broken plastic gears and others parts i need do yoy know where i can find a detailed part list for the ds2114 and dealers non only in itsly where i can order them many thanks carlo giacch perugia italy.

Suggested Questions And Answer :


Plastic gear I cannot find suppliers for my broken plastic gears and others parts I need. DO yoy know where i can find a detailed part list for the ds2114 and dealers non only in Itsly where i can order them? Many thanks. Carlo Giacch? - Perugia - Italy


L have gears and servos@mail my atzlatko12003@yahoo,com
Read More At : DS-2114 ATS (325 x 114mm) Telescope...

I have a broken elevation spindle, the little aluminum casting that passes through the plastic driven gear and ultimately ends in 4 tapped holes that the sleeve bolts to that holds the optical tube. We tried to repair this with JB Weld Epoxy, and it held for one night, but it broke again when moving the scope. Is a replacement spindle casting available from any source? Although I am an engineer, and if money were no object, I could probably reverse engineer this part, produce a blueprint from many careful measurements, go to a foundry, and have a new one cast (or drop forged) in stainless steel, it would cost many times more than the telescope itself, and for that price I could just get a much bigger scope with a far more rugged mount. The original damage happened when the motorized mount was in a duffel bag that someone knocked off the tailgate of a pickup. It fell about 3 feet and impacted on hard rocky terrain. Visually it appeared to be undamaged until the weight of the tube was applied, then it was obvious something had broken. I have some pictures of the part and exactly where it goes if it has a different name than what I described. So i need a good part number for this part, a valid address and price and delivery information to order one from. If someone has built an aftermarket one from something like stainless steel or similar stronger material, so much the better, as it might also stiffen the scope and reduce vibration and oscillation when one bumps the eyepiece while observing.


Meade "MAY" sell you the part? Usually they want you to send the scope back. Call customer service:http://www.meade.com/support/index.htmlThis is also a problem on the ETX model scopes. There are some ingenious fixes posted on the Mighty ETX web site.Here:http://www.weasner.com/etx/menu.html Bassically bolts, washers and nuts.Search the web site for Broken DEC knob.
Read More At : DS-2114 ATS (325 x 114mm) Telescope...

Good morning (in Brazil). I cant find WHERE to place the battery ON red dot finderscope; should it be placed where the plastic insulator is? I cant find a case, or whatever it is.


Most red dot finders use small watch style batteries. Look for something that slides out of the red dot finder and or a port in the side or the bottom.
Read More At : NorthStar 78-8846 (675 x 114mm) Telescope...

Finding replacement rubber eye pieces for my binonculars


These are the guys you need to contact if you are in the USA; http://www.bushnell.com/general/binoculars_legacywp.cfm?section=General%20Use They make a lot of the binoculars for B+L who make the optics, including the legacy models. Hope this helps :) If not in the US please ask again
Read More At : Legacy 12-1056 Binocular...

I can't find the battery for the Bushnell Voyager finderscope


In shop
Read More At : Voyager 78-9945 Telescope...

HOW TO FIND MODEL #


Hello how are u doing
Read More At : Explorer NOCX3G Monocular...

Also lost right hand eyepiece


Wich model do you have as i have some parts for older models...larry 5088331232
Read More At : Travelite V Binoculars...

Binoculars barrels won't stay in position, need tightening tool


Try needle nose pliers
Read More At : Northern Tool...

Me too! http://www.astromart.com/classifieds/details.asp?classified_id=643311 I am also looking for a Dec Fix kit for my 8" LX-50. Have tried many sources.. including AstroHut.Com (now Scope Logic) which no longer carries the kit. =( If you find one.. please let me know. Thanks!


You might try www.scopestuff.com They have one for an LX90, and an LX200.
Read More At : LX50 (8105003) (500 x 203mm) Telescope...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.opticinfobase.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0311 seconds